Hot News
Contact
- Contact Person:Mr. Du
- Phone:+8613609288011
- E-mail:tina.gatn@wolongcne.com
- ADD.:No.1801 Dushan Avenue, Nayang City Henan Province, China
Notes on bearing lubrication
source:未知 time:2024-12-20 09:25nbsp; click:
1. Most small motors have adopted double-sealed bearings (with "ZZ" after the bearing model). This type of bearing is pre-oiled and does not need to be re-oiled.
2. Motors with oil filling and draining devices have been filled with oil when leaving the factory, but after the motor is used, it is necessary to regularly add grease according to the time, grease brand, and oil filling amount on the oil filling label.
Bearing oil filling method:
Open the oil filling nozzle, make sure the oil filling nozzle is clean, connect the oil filling nozzle with a manual oil gun or a pneumatic oil gun, and inject grease according to the time, grease brand, and oil filling amount on the oil filling label.
If there is no way to control the amount of oil filling, you can open the oil drain port when refueling. After refueling, let the motor run for 20-30 minutes to allow the excess grease to be discharged, and then cover the oil filling nozzle and the oil drain port dust cover, and the refueling is finished.
If the bearing grease is too much, it will cause the bearing to fail quickly without draining the oil.
Type of lubricating grease:
When refueling, be sure to read the grease brand on the oil filling label and use the correct lubricating grease. If the added grease is incompatible with the original grease, the life of the bearing will be greatly reduced.
Electromotor, elektrik motor, elektronik motor
2. Motors with oil filling and draining devices have been filled with oil when leaving the factory, but after the motor is used, it is necessary to regularly add grease according to the time, grease brand, and oil filling amount on the oil filling label.
Open the oil filling nozzle, make sure the oil filling nozzle is clean, connect the oil filling nozzle with a manual oil gun or a pneumatic oil gun, and inject grease according to the time, grease brand, and oil filling amount on the oil filling label.
If there is no way to control the amount of oil filling, you can open the oil drain port when refueling. After refueling, let the motor run for 20-30 minutes to allow the excess grease to be discharged, and then cover the oil filling nozzle and the oil drain port dust cover, and the refueling is finished.
If the bearing grease is too much, it will cause the bearing to fail quickly without draining the oil.
Type of lubricating grease:
When refueling, be sure to read the grease brand on the oil filling label and use the correct lubricating grease. If the added grease is incompatible with the original grease, the life of the bearing will be greatly reduced.
Electromotor, elektrik motor, elektronik motor
上一篇:Why can't the motor be started frequently? | 下一篇:Motor should be equipped with a moisture-proof heating devic
Recommend MORE+
-
YB3 High-pressure explosion-proof motor
-
YFB3 Low-voltage dust explosion-proof motor
-
OLI Explosion-Proof Vibration Motors
-
YBC Coal Mine Flame-proof Motor
-
YB3 high voltage explosion-proof motor
-
YZYKK High Voltage Positive Pressure Asynchronous M
-
YBRB Flame-proof AC Motor
-
TZYW Series Positive Pressure Brushless Excitation
NEWS MORE+
- Motor common problem treatment method 2025-03-21
- Application scenarios of different motors 2025-03-20
- What Are the Causes of Abnormal Vibration and Noise 2025-03-19
- What are the causes of motor overheating? 2025-03-18
- High Voltage Synchronous Motors: Key Application Sc 2025-03-17
- What Causes a Motor to Heat Up? 2025-03-17
- The Excellence of YBX3 Explosion-Proof Motor: A Key 2025-03-14
- Does the motor sliding bearing use the thin oil sta 2025-03-14
- Explosion-proof motor and ordinary motor difference 2025-03-13
- The magnetic shunt effect of the shaft in the motor 2025-03-10