How to configure motor bearings?_Wolong Nanyang Explosion-proof Motor, China Motor Manufacturer

Hot News

Contact

Contact Person：Mr. Du
Phone：+8613609288011
E-mail：tina.gatn@wolongcne.com
ADD.：No.1801 Dushan Avenue, Nayang City Henan Province, China

How to configure motor bearings?

source：未知 time：2024-06-05 09:55nbsp; click：

The rotor part of the motor product usually needs to be supported by two sets of bearings, and the rotor is radially and axially positioned relative to the stator. According to different usage requirements, such as load, required rotation accuracy, and manufacturing cost requirements, the motor bearing configuration generally adopts: one end fixed and one end floating configuration; two ends fixed pre-adjustment configuration; two ends floating "floating" configuration, etc.

01
One-end fixed, one-end floating configuration

The fixed-end bearing is fixed by the shaft and the end cover bearing chamber at the same time, providing radial support at one end of the shaft and playing an axial positioning role in both axial directions. The bearing at the fixed end must be a radial bearing that can withstand combined radial and axial loads. Deep groove ball bearings are the most commonly used in motor products. In some other equipment and machinery, double-row or paired single-row angular contact ball bearings and other bearings that can withstand combined loads are also used.
For motors with three-bearing structures, positioning is performed by a bearing combination, that is, a radial bearing that can only withstand pure radial loads (cylindrical roller bearings with no flanges on the rings) is combined with a deep groove ball bearing that can withstand combined loads. In this configuration, the other bearing, the deep groove ball bearing, is only used for axial positioning in two directions, and a certain radial degree of freedom must be left in the bearing chamber, that is, a clearance fit with the diameter direction of the bearing chamber.

The floating bearing of the motor is at the other end of the shaft and only provides radial support. Therefore, the floating bearing can be a deep groove ball bearing or a cylindrical bearing. For motors with large loads and impact loads, cylindrical roller bearings are used in most cases. In this configuration, the shaft must be allowed to have a certain axial displacement so that there is no mutual force between the bearings. During the operation of the motor, when the shaft expands due to heat, axial displacement can be achieved inside certain types of bearings (cylindrical roller bearings). Axial displacement can also occur between one of the bearing rings and the parts connected to it, preferably between the outer ring of the bearing and the bearing chamber. In view of this, the designer needs to conduct comparative analysis and demonstration to choose N-type or NU-type bearings.
There are many different combinations of bearing configurations for the fixed and floating ends. The following are some of the more commonly used combinations. For rigid bearing configurations, combinations that can achieve axial displacement in the bearing should be used, such as: deep groove ball bearings and cylindrical roller bearings; double row angular contact ball bearings and cylindrical roller bearings; paired single row tapered roller bearings and cylindrical roller bearings. Of course, there are other combinations. For this aspect of design, it is recommended to conduct joint analysis and selection with the bearing manufacturer.

In the above combination, the angular error between the shaft and the bearing seat must be minimized. If the application does not allow, it is recommended to use a combination of self-aligning bearings that can withstand larger angular errors. These configurations can withstand certain angular errors and axial displacements, and can avoid internal axial forces in the shaft system. For bearing configurations where the inner ring bears rotating loads, the length change of the shaft needs to be adjusted between the bearing and its mating surface, and the axial displacement should be between the outer ring and the bearing chamber. The most commonly used combinations are deep groove ball bearings and deep groove ball bearings; paired single-row angular contact ball bearings and deep groove ball bearings, etc.
02
Floating bearing configuration

Floating bearing configuration is also a cross-positioning method, suitable for applications where only moderate axial positioning is required or there are other parts on the shaft for axial positioning. In this configuration, the most important thing is that each bearing can be axially displaced. This can be between one of the bearing rings and its mating surface, but preferably between the outer ring of the bearing and the bearing chamber.
03
Pre-adjusted bearing arrangement

In a pre-adjusted bearing arrangement, the shaft is axially located in one direction by one bearing and fixed in the other direction by another bearing. This arrangement is called "cross" positioning and is usually used for short shaft lengths. All radial bearings that can withstand axial loads (in one or two directions) are suitable for this arrangement. In some cases, single-row angular contact ball bearings or tapered roller bearings are used in a cross-positioned arrangement, but some preload may be required.

上一篇：Advantages of variable frequency motors | 下一篇：Vertical Motor Noise Fault Analysis

Recommend MORE+

NEWS MORE+

Starting method of three-phase asynchronous motor 2024-11-22
Analysis of the causes of three-phase AC motor burn 2024-11-21
Analysis of the mean trouble-free working time of m 2024-11-20
What is the function of current transformer? 2024-11-19
Generation and Harm of Corona in High Voltage Motor 2024-11-18
Energy-saving transformation of dust treatment scen 2024-11-15
Why do low-pole-number motors often have phase-to-p 2024-11-14
Introduction to commonly used motor drive modules 2024-11-13
Differences between vertical and horizontal motor t 2024-11-12
Wolong YBX series explosion proof three phase low v 2024-11-11